Start with the protein reporting basis
MPC grade numbers are shorthand for protein content, but a number alone is not a complete specification. Before comparing MPC 70, MPC 80 and MPC 85, find out whether the protein value is reported on a dry basis or as-is. Those bases answer different questions: dry-basis protein excludes moisture from the calculation, while as-is protein reflects the powder as received, including its moisture.
This distinction can matter particularly when using a standard that defines MPC 70 and MPC 80 on a dry basis but expresses MPC 85 as-is. That convention is not a universal rule for every supplier or specification. Check the named standard and its current edition, then compare the supplier’s specification and lot analysis against the basis it requires. A grade label without its basis can make unlike values appear directly comparable.
To convert between bases, use the moisture value from the same analysis: dry-basis protein equals as-is protein divided by the dry-matter fraction; as-is protein equals dry-basis protein multiplied by that fraction. Keep the units and sample basis consistent. The calculation can help normalize figures for comparison, but it does not replace compliance with a standard’s stated test and reporting requirements.
Treat a grade label and a lot result differently
A standard or product specification describes the reference requirements for a category or grade. A certificate of analysis, or other lot analysis, reports results for a particular lot. Neither should be mistaken for the other: a grade name does not establish the measured protein value of every shipment, and a lot result does not by itself establish which standard or edition the product is represented against.
When reviewing a specification, identify the issuing standard, edition, grade definition, protein basis, units and analytical method if stated. Then compare the lot analysis using the same terms. If a limit is relevant to your purchase, verify it in the named current standard rather than relying on a remembered industry convention or a supplier’s shorthand grade name.
This is especially important when the standard changes the reporting basis between grades. An MPC 85 value reported as-is cannot be read as though it were an MPC 85 dry-basis value. Establishing the basis first avoids a misleading ranking and gives quality teams a clear criterion for evaluating a lot.
Read lactose, fat, ash and moisture alongside protein
Protein is central to the grade comparison, but it does not describe the whole powder. Lactose, fat, ash and moisture account for other parts of the composition and help explain why two products with similar protein figures may not be equivalent for a formulation. Review these values together rather than treating them as optional details.
Lactose is milk carbohydrate; its amount helps distinguish the composition of MPC products and may affect how an ingredient fits a formulation. Fat contributes to the powder’s composition and can matter when a product’s intended use calls for a particular fat level. Ash represents mineral content, so it completes the compositional picture rather than serving as a substitute for protein measurement.
Moisture is essential to interpreting protein basis: it determines the relationship between the as-is and dry-basis figures. It is also a distinct reported characteristic, not something to infer from the grade label. For a meaningful side-by-side review, compare each constituent on the same stated basis and check whether the listed results are specification limits or measured lot values.
Build a like-for-like comparison
A useful comparison sheet records the product name and grade; the governing standard and edition, if applicable; protein value and basis; moisture; lactose; fat; ash; units; and analytical method where supplied. Mark each entry as a reference limit, target or lot result. This makes it easier to spot a missing basis or a mismatch between a specification and its analysis before the product is evaluated for a formula.
Do not rank MPC 70, 80 and 85 from the number alone. First normalize the protein basis for analytical comparison where appropriate, then check whether each value meets the definition being applied. Next assess lactose, fat, ash and moisture against the product’s intended use and internal quality criteria. A higher protein figure does not automatically mean a better fit if the rest of the composition or the documentation differs from the requirement.
Once the required composition and reporting basis are clear, compare offers against that same specification. For buyers sourcing milk protein concentrate, the [Milk Protein Concentrate 70/80/85 page](/ingredients/milk-protein-concentrate-70-80-85) is a natural next step for reviewing the ingredient and pursuing a suitable product specification.
Common questions.
Can I compare MPC 85 directly with MPC 70 or MPC 80?+
Only after checking the protein reporting basis. Some recognized specifications express MPC 70 and MPC 80 on a dry basis and MPC 85 as-is, but conventions are not universal. Use the named standard and its current edition, and compare values on the required basis.
Why do lactose, fat, ash and moisture matter if the grade is based on protein?+
They describe important parts of the powder that protein alone does not capture. Lactose, fat and ash help distinguish composition for formulation review, while moisture also determines how an as-is protein result relates to a dry-basis result.
Does an MPC grade label prove that a lot meets the specification?+
No. A grade label identifies a product category, while a lot analysis reports results for a particular lot. Compare the lot results with the applicable specification, including its basis and analytical method where stated.